We've received many photos of the origami dragon folded by readers. Origami Dragon Step 11: And there you have it! A fearsome, cool looking origami dragon! Origami Dragon Step 10: Almost there! Now use simple back-and-forth pleat folds to make the wings more dragon-like: Origami Dragon Step 9: Now use reverse folds again to form the tail of the dragon: Origami Dragon Step 8: Now make two more reverse folds to form the mouth of the dragon: It uses the same base and initial folds as the. Follow the next ten (10) photos to make the neck of the dragon. Hello everyone, in this video Im going to show you how to make one of the the easiest dragon origami I know. The reverse fold is explained in detail in the origami flapping bird instructions. Origami Dragon Step 7: Now it's time to start folding the neck of the origami dragon, using a sequence of three (3) reverse folds. Fold corner E upwards, then repeat on the backside. Origami Dragon Step 6: Repeat this fold on the backside to form the second wing.

It's now time to start making the dragon wings, by fold the edge E-F to the vertical position, as shown below right: Origami Dragon Step 5: Now fold corner D backwards to give the result shown below left. Origami Dragon Step 4:Now fold the corner C from left to right, around the dotted line: Next, fold the corner B back and downwards: Origami Dragon Step 3: Fold the corner A upwards. Origami Dragon Step 2: Now fold the rear flap down and back: Fold the opposite corners of the diamond to the centerline as shown. Origami Dragon Step 1: To make this origami dragon, start with the origami bird base. Take the bottom left side of your paper, and perform an inside reverse fold-in other words, fold the paper up towards the center of your paper. Now that you have finished your petal folds, we can make the head and tail of the dragon. You can watch our Origami Dragon Instructions Video, or follow the step-by-step photo instructions below. Step 3: Fold the Head and Tail of Your Dragon. The origami dragonfly starts from bird base. This page is for those who want the instruction to fold a traditional origami dragonfly. For me, the dragon flies the farthest when its wings are angled slightly upwards, and if the throw is relatively light.Made this origami? Comment and Submit your photo using the comment box at the end of this page! How to make a traditional origami dragonfly.

Angle of wings and the strength of your throw.

If the dragon is not very aerodynamic, it will not fly far. Bigger wings are better, and a wing shape that is aerodynamic and allows for lift works better. Sometimes if the weight of the dragon is uneven, paper clips will help to balance it while in flight. You are finished! If you want to decorate or experiment with the dragon to make it fly farther, go ahead! If the only glue type that is is available is bottled glue, wait until the wings are completely dry to fly your dragon.

If this occurs, use a glue stick to glue them back together. Note: If you cut off too much from the dragon's wings, the layers in the wings may separate. You can also cut the wings of the dragon slightly so that they have a design/fly better. Once this is done, get a pair of scissors and cut an arc in the back, legs, and neck of the dragon to reduce its weight.

Fold the wings horizontally so they are even. Repeat this process wit the dragon's tail, with the only difference being that the tail's fold is smaller than the head's. As in the picture above, hold the neck with one hand and push the head of the dragon down until you see an arrow-like shape. The last couple steps to folding are to shape the dragon's head and tail. Once complete, the paper should currently look like a diamond with a sideways 'tail', as seen in the picture above. How to make paper origami dragon fly - EasyYellow Paper Origami, this video will show how to fold paper origami dragon fly with a turning turret from origami. Once the top layer is completely opened, flatten the entire layer down into a diamond shape. Note: Be careful when opening this layer, as the bottom layer could unfold with it. Once your layer is standing up, open the layer that is standing up. Once you have done this step, unfold the top layer and make it stand up vertically, as in the picture shown. It should form a thick triangle with two layers. Start with a horizontal fold towards the bottom of the paper, as seen above. Make sure your paper is oriented like the photo shown above. Once you have your square paper, you are ready to start folding. If you are using printer paper like I did in these photos, make sure you cut the paper into a square before you start folding your dragon. In this example, I used a piece of standard printer paper. The lighter the paper is, the better the dragon will fly at the end. Start with a simple piece of square paper.

Origami dragon that flies